AEON Configurator

Not just another mass produced frame, you’ll notice and feel the difference the moment the AEON frame is in your grip.There was a no compromise focus in our quest of  finding the best carbon sheets available to cut from. The plain twill 4mm carbon with 0-90 degree uni-fibre layup runs length-ways down each arm, maximizing the strength of the carbon and arms. It’s central X structure at the core, will ensure any force from impact is consistently spread across the entire design.Each frame is machined with a bit that had to be custom ordered to meet the specifications of the cutting process. Once cut the edges are finished with a slight chamfer and each frame is hand cleaned and polished, giving an amazing smooth as silk feel.

Tested by respected pilots, the design of the AEON has been proven flight after flight and crash after crash.

• Ultralight designs offer a minimum weight build when paired with our POD
• Frame support for standard 30.5 mm X 30.5 mm stack
• The AEON UL12 is the lightest frame on market with 5″ prop clearance

The AEON Lipo Pads are made of a high grade silicone with a perfect blend of pliability and grip. 2mm thick candy red silicone Backed with 3M adhesive, they will ensure your lipo stays locked in. Choose the right set for your AEON UL12, UL16, or HD frame.

The AEON POD set is versatility at its finest. A perfect blend of lightweight compact design and strength. With a 30.5×30.5 (universal) base, and mounting points for 20×20 and 16×16, it offers a “Christmas tree” build up design, allowing you versatility in building with many different variable setups. The camera hood with it’s petal design offers front protection to the lens of the cam while keeping a minimal type appearance that flows into the POD so the cam design itself can be seen. Made specifically to use with the Runcam Micro Swift V2 or the Foxeer Micro Arrow, the hood offers stopping points of 35 and 45 degree camera angle or flip upside down to offer 15 and 30 degree angles.

*Note: Other hood options for other micro camera options on the market will be available soon.

• Coming in under 6 grams the POD makes for a light and compact build
• Extra’s are included, such as standoffs, bare cam mounting pads, and AXII Antenna adapters to give more versatility to your build
• A new production process brought to the drone industry offers superior rigidity to flex ratio

The AEON POD Hardware Set gives you all the screw assortments you need to complete your POD build. The aluminum is cold rolled rather than machined. This not only creates a much stronger hardware, but is also a higher cost to produce process. This hardware was created to be some of the best you’ll find and will outshine much of the cheaper machined 7075 or often used 6061 hardware found on the market. Finished off in a red anodized custom finish, the 7075 T6 cold rolled aluminum offers only the highest quality .

We spent a lot of time looking for lipo straps that break the standard. Durability, design and detail were the top 3 requirements. Test after test has proven for what we believe to be some of the best straps on the market. Most straps use a hot pressing method for holding the buckle in place. This often times becomes a weak spot after the strap gets pressure applied time and time again from strapping down your batteries. Our strap uses a Kevlar stitching to ensure even the tightest of tension doesn’t break down the strength of the strap. It’s not only applied at the buckle end, but the stitching travels down both sides of the strap, so no more fraying or layers separating.

At under 26g with short wire, this weight best previous generation 2305 by 3-4g. Each gram saved at the end of an arm, decreases the lever forces that occurs during unintended crash landings. Effectively minimizing the chance of critical damage. While in in the air, those grams savings help maintain roll and pitch agility. Performance gain by refinement, rather than simply adding to stator size and mass. The trifecta of lightweight, performance and design is unlocked when combined with our AEON frame and POD. Add to that the unmistakable and design and attention to details for a true work of art!

For those wanting to build the POD with an All In One (AIO) 4n1 ESC/FC board and want extra strength added to the structure the 20x20mm carbon support will not only offer you extra strength in the central POD structure, but also give you an x-brace plate for mounting extras such as your Rx of vTx board.